Видео

R5 is 0.1 ohms or 100M ohms ? the smallest i found at my retailer is 0.56 ohms, can I put this instead ? (I'm complete beginner btw)

I love seeing videos like this with half a million views!

PIC is absolutely horrible for hobbyists. I only got good with it because I learned to use PICs in college and had a good TA who showed me the ropes. Even then, I switched to AVR for hobbyist projects because the support is so much better.

Can these chips be programmed with a raspberry pi or Arduino?

The step by step explanation of the Dickson pump is brilliant, it shows very clearly how the capacitors sort of "bucket brigade" their charge along the circuit

awesome video! Seeing you use a WM makes me miss it so much. I used to play with dwm, i3wm a lot. Now I just use gnome but maybe someday I'll comeback to what I prefer.

Copy preamp boards from famous high quality condenser mics. They also sell them prebuilt on your favorite e-commerce sites.

Bro, dw01 chip activates over discharge protection at 2.4v which overtimes permanently damage the battery capacity, if the load is low dw01 can destroy a liion battery in ony cycle. 2.4v is even more detrimental to.lipolys. A better chip I think is fs312f. Make a video about it, and reply me.

Hi, great video!! Aquestion out of curiosity... in the case of your discrete project, couldn't you correct the offset by adding a DC servo loop? Thank you!

Could you please tell me what component model specs you used? Like the type of capacitors,diode. And what is the max current that can generate?

Very nice, I am eagerly waiting for the MOSFET video.

Can you explain to me what are the advantages of adjusting your linker files compared to IDE and automatic adjustment?! You can still use everything when using IDE.

Hope to see great contents from you

Im upgrading to a heat sink with a new SSR i had to replace in an infrared conveyor belt dryer. The new dryers come with heat sinks, mine failed after 19 years so i dont think i need the heat sink but after your video i realize a 50A 3-35vdc input and 24-280vac output probably needs it. Thank you

Gosh, pretty close to "bare metal" programming... That's going to turn off some Arduino users, but, hey....

Coincidently, I just picked up a Nucleo to play with an STM32 for the first time. So this is very helpful. But I'm wondering, are there no pre-generated header and linker files for these chips? I'm used to writing code for ATMega chips in Atmel Studio, and there it provides all the various utility files. Is this because you chose to not use the STM IDE? Was that just for educational purposes, or is there some reason you don't like it? (If this was answered in the video, I missed it...)

You're hired!

After watching Ben Eaters 6502 series and building his breadboard kit this is a definitely a great introduction into a step into 32bit. A lot more to take in but easy enough to build on existing microcontroller knowedge to take the next step. Sounds like you played on hard mode and there's some tools to avoid some of the low level stuff you've done. But it's great to get an overview of the process and the ins and outs to really get understanding of how it fundamentally works. Love your videos

But also this video we need . Good job .

Where is class D part 3 ? ❤

How did you find the navigation of that 1000 page manual to be? Is it as straightforward as your demonstration or does it require a lot of prerequisite knowledge to follow along? Thanks for taking the time and doing what I trust to be a complete bootstrap procedure for us.

Haha this video is super hardcore 🫣 You have great knowledge about the fundamental working of a STM32 MCU. I like STM32 but I would never ever do my own linker files. I just use the STM32 IDE for c programming and the initial code is generated by the Cube MX. The NUCLEO boards are comparable to an arduino board. And they have a ST-Link programmer included!

Well I shan't be buying an STM32 anytime soon LOL !.....cheers.

What language used to write the linker file?

Professors should use your this walk-through to teach. Well said. I'm new to all of this, but I've been "grazing" info / tinkering for a year or so in my freetime, and the makefile walk @18:30 is the first one I didn't want to speed through or kill myself watching - Ty for that ^^

i really didn't like your fraud

I want a $0.10 8-bit MCU that I can program using its own assembly language and/or C without an extra piece of hardware (programmer) and without any IDE whatsoever. Heck if it were even $2 I would take it. Just let me send some ASCII text code from whatever text editor I like to a cheap but capable MCU.

PIC: programmer (hardware piece) is expensive and obsolescence comes quick. IDE is trash .. heavy and difficult .. older more nimble version was better, but no longer supported. The chips themselves are fantastic, indestructible, capable works of art. Datasheets are done well. AVR: easy to use, internet drowns in its accolades, fanbois, and docs. Any 80 iq newbie from any random 2-bit country can put together a usable widget using an arduino. The chips themselves appear to be fine to great. But the usual packaging leads noobs to look for software solutions where they should be learning hardware components and capabilities. Most of the projects I have seen using either could be replaced with <$.0.50 worth of 555 or op amp or both including supporting components. Maybe that is bc a lot of YT projects are of the proof-of-concept variety, idk. But point stands. Nice vid, though, I appreciate you making and sharing it, and I enjoyed it. Thanks.

The Pickit3 and the MPLABX are buggy, but at the end of the day they float the boat. The PIC-based end products always worked really great, I've been developing such products since 2016 with great success in low cost, low power consumption, versatility and reliability. I've seen no need to change uC families so far!

At 5:56 should the formula be Vo / Vin = Z2 / (Z1 + Z2) ?

What is TP11?

Nice tutorial. For another elementary intro to oscillators I suggest looking up the video "Lab 04 Oscillator design" by Mazhari.

So much info in relatively short video, I like that! Quality work, thanks.

Uhh yeah, any "negative" resistance is a voltage source..

Cool but naaah, for all that effort I'd rather just get UTG962E, its incredible how good those for the price.

I used charge pump for my class A power amp i had built years ago... To boost the voltage for pre amp part..

a discrete class D amp ... that IS interesting

Why is the RUclips algorithm showing me this video after a long time, it should've shown me when I needed it !! Intuitive and Infotainment. Thanks a lot, bruv!

Thank you for this. I'd love to see some comparison regarding RF immunity. I've seen problems with the LM358 where it appeared to rectify an RF field which then causes problems in an audio circuit. I'm sure a resigned circuit with better shielding would work, but the quick fix was to switch to a TLO72 or TLO82.

Superb, however, need to discuss input and output impedances of common base, common emitter, and common collector configurations.

Is there anyone here that could clone my PIC16C58B 04/P from my washing machine's motor controller?

Very well explained

Microchip also makes a budget version of the PICkit4 called the "MPLab Snap."

Nder if a form of a heat sink could be used for siding on a house to reduce heat.

I'm looking for a wireless USB extender, that is, one part acts like the male "A" end, the other acts like the female "A" end, and they connect by radio link. Neither the host nor the appliance know it's there. It would appear to be a cable, except the female/appliance end would supply the 5V power. Can you please point me to such a device?

Just what i need, good topic and explanation mate. Good job mate! Subscribed, if I have spare time I will watch another topics.

Nah, if i use something i just need to know what happen. So before just using stepper driver ic i just want to try manual mode. But, i am too lazy to make my own h-bridge so i use ir2110, then i was too lazy to calculate deadtime so it was ir2153😆

Should feeding the output of the first Inverter to both a buffer and another inverter to get rid of the time difference between the first stage and the second stage out of the equation?

Best video thus far on this topic!

Excellent....as a circuit designer and a PdD student I request you to please make videos on MOSFETs and related circuits like bootstraping ,etc